In Reply to: Got feedback from Midas guy posted by bert on April 05, 2001 at 12:25:39:
He was able to non-conclusively determine that the power flow regulator is out of wack....he said that it's the part that distributes the flow of the 'mineral oil'(power steering fluid) to the brakes, power steering and the LAD. He wasn't able to say for sure because he doesn't have the right fittings, etc. to run the pressure tests needed. Best bet is to take it to a dealer or import car shop to get it diagnosed.
....more to come...
Talked to a couple guys to try to figure this one out. Guy from Midas, agreed with this other what I consider 'car expert', said that it's probably the hydraulic assist. If I remember right, the power steering hydraulic assist also works on the LAD and as the brake assist (booster).
Taking it in to him tomorrow to check and get a full brake system diagnosis.
I'll write again tomorrow night after he checks it out and tell you his diagnosis.
Fluid replaced last month. I rebuilt all four calipers to eliminate a sticking piston or two as the cause of the problem. Calipers were in good condition (bolstering my long ago argument that preventitive rebuilding of calipers is probably not necessary). Anyway, caliper rebuild could not hurt and cost was only about $20.00/corner.
I don't know how often you relace the actual brake fluid, but that can be a problem too.. not the base cause, but old fluid with ANY water content in a "dragging shoe" (yes, I lnow they're pads, that's the term I grew up with!) situation to heat that fluid up will end up adding pressure as the water tries to boil in the calipers behind the pistons....
I only know this as I had a similar situation on a K100 BMW bike rear brake one time... over adjusted so the caliper dragged, only noticed when I started slowing down after a long highway ride. Eventually forced to stop as rear brake locked on, 5mm stainless rotor was a nice "blue"!! est abt 200C, took over 1/2 hr before I dared start flicking water at it GENTLY to aid sooling, it was that hot. Oh well.
Our symptoms are EXACTLY the same. Although it sounds like yours is worse. The rotors probably warped due to excessive heat from the draggin brakes. So, for sure, fix the dragging problem BEFORE you replace the pads/rotors.
I am going to check if I have an adjustable actuator rod/link from pedal to booster. If I do, I will adjust in some slack to eliminate this from the equation (i.e. booster not returning fully).
Yes, the pedal's returning to the normal position but the phenomenon is the same...different every time I get in. The interesting thing is that when the car is first started in the morning, the brakes work fine. It's only after driving for a while and it seems worse in stop and go traffic.
Coupled with the warped rotors, the car shakes violently when it hits just the right resonance at about 50mph. (already got the rotors and brakes ordered but want to get to the root of the problem before I stick them it).
It's going to be a learning experience since I've never done anything on brakes besides replacing rotors and pads.
Thanks for the advise. Keep me posted on your findings! I'll take a stab at your suggestions this weekend.
My 88 750 is starting to do the same thing after prolonged stop and go traffic. Some have suggested that the master cylinder is the problem. My pedal IS returning to the normal position. Is yours?
Since my problem is intermittant, I cannot perform the following, maybe you can:
1. Loosen master cylinder mounting bolts at brake booster. If brakes release, then I would suspect the booster is not returning. Check for pedal obstructions that would prevent the pedal from returning to normal position. Otherwise, suspect a faulty booster.
2. If no changer after step 1, then crack a pressure line or two. If brake(s) release then suspect a faulty master cylinder.
One interesting fact on my car is that the pedal never really feels the same from day to day or stop to stop. I really am leaning toward the master cylinder and possibly a weak accumulator.
And no....don't say because I'm pressing the brake pedal or the emergency brake is on :)
The brakes don't seem to want to retract back.
What could be causing this? Need help desperately!