The complete automotive resource for buyers, sellers, and owners like you.
Car, Truck and SUV Forums at Roadfly
+ Bentley Forums
+ BMW Forums
+ Cadillac Forums
+ Chevrolet Forums
+ Ferrari Forums
+ Jaguar Forums
+ Lamborghini Forums
+ Lotus Forums
+ Mercedes-Benz Forums
+ Maserati Forums
+ MINI Forums
+ Porsche Forums
+ General Discussion
+ Marketplace Forums
Good instructs & if owner doesn't want to tackle (archive)

[ Follow Ups ] [ Z3 Message Board ] [ Msg. Board FAQ ]

Posted by SL on April 05, 1999 at 08:25:04:

In Reply to: Step by step instructions posted by Doug96 on April 05, 1999 at 08:12:06:

because they aren't very nimble-fingered, they could order the kit and then get a quote from any reputable auto upholsterer for just the labor. I bet total cost would still be less than half what you were quoted from dealer (who may be farming it out to just such a shop anyway and then doubling or tripling their cost!)

: The installation was pretty easy.

: The instructions that come with the window were good. Very few parts; the window, a zipper, two little metal clips, a short piece of double sided tape (100 MM) and a plastic piece that looks like a tongue depressor.

: The hardest part for me was getting the zipper started on the new window.

: 1. Unhook the top
: 2. Run the plastic tool between the black rubber bead and the existing window to break the bind between the top material and the double sided tape used on the window. (I almost quit at this point because it looks like you are tearing up things... but donít worry.... the new window comes with all new parts).
: 3. Pull the black rubber bead off and discard (a new one is attached to the new window.... to my relief!)
: 4. Remove the metal clip at the bottom center of the window. You have to loosen it from inside the car, and then remove from outside. (easy)
: 5. Unzip the existing window. Discard. (easy)
: 6. Clean any reaming rubber cement off of the cloth. We used a cloth and rubbing alcohol. (easy)
: 7. Zip in the new window. Itís important to follow the instructions and start with the blue side. This was the hardest part. I had a very hard time getting the zipper started. I did learn that you can start the zipper standing outside the car. I found this a lot easier than trying to do it from the inside. (Zipping the window takes two people... one on the outside holding the window and one on the inside running the zipper).
: 8. Insert the metal clap to insure that the zipper does not come undone. I used both clamps that came with the new window although the original window only had one clamp. (This takes two people.... one on the outside and one on the inside) (easy)
: 9. Apply extra 100 MM double sided tape to area where claps were installed. (easy)
: 10. Apply rubber cement to the cloth top Ė where it meets the double sided tape on the window. (easy)
: 11. Expose the sticky side of the double sided tape by removing the protective plastic. (easy)
: 12. Use the plastic tool to push the edge of the top into the black rubber bead around the window. (not too hard... be patient).
: 13. Run your finger around the cloth top pushing it against the tape and into the rubber bead. (easy... your almost done).
: 14. Fasten the top and leave it up for 24 hours.

:
: I will definitely do this again. I canít believe that the dealer wanted $600 for this job. Guess they think Iím made out of gold since I own a BMW!

: Doug96


: : I remember reading about the window replacement on mZ3.net. The author there reported that this job was not recommended and was a real pain in the rump. For me, I find that keeping rear window scratches to a minimum is the most difficult maintenance issue with my '99 2.3, and I suspect that my anal retentiveness will eventually lead to replacing it every so often to keep the car looking new. Can you give a summary of how you did this job? What was most difficult? On the surface, looks like a simple zip out/zip in deal, but it can't be that easy, right? I assume the window is $100? Thanks!

: : : Well, my wife and I replaced the rear window on our Z3 today despite the warnings from this message board. We decided to do it after the dealer (Hendrick BMW of Charlotte NC) told me that their cost to replace the window would be $600. I couldnít believe the cost! I asked two different service advisers on two different days and got the same quote $600.

: : : Instead of making Hendrick any richer, we decided to tackle the job ourselves. I ordered the window from Quality Imports for a reasonable cost. The window from Quality was genuine BMW and it arrived in great condition.

: : : The job only took about 2 hours for us to do. Next time it will probably only take an hour or so.

: : : Donít be afraid to replace your window. It does take two people, but itís relatively easy to accomplish.

: : : Doug96




Follow Ups:



[ Follow Ups ] [ Z3 Message Board ] [ Msg. Board FAQ ]
Questions, comments, or problems, please visit the Roadfly help desk.
Roadfly.com Logo © 1997 - 2017 Jump Internet Inc. All rights reserved.